冬季北方已經過了一半，但是不少GRC構件廠家堅持冬季施工，施工要有溫度保證，這樣才能確保施工質量。那么冬季進行外墻裝飾GRC構件的施工過程中，有哪些防凍的注意事項呢？下面濟南GRC構件廠家為您講解。

Half of the winter has passed in the north, but many GRC component manufacturers insist on winter construction, and the construction should have temperature assurance, so as to ensure the construction quality. So what are the precautions for frost prevention during the construction of GRC components for exterior wall decoration in winter? Next, the manufacturer of Jinan GRC components will explain it to you.

在安裝之前，根據設計圖紙將高程、水平線、直線和部件控制線鋪設到外墻，使部件控制在同一水平。構造外框時，考慮設備的特點和外框的外框尺寸，以保證設備外框有一個令人滿意的距離。

Before installation, the elevation, horizontal line, straight line and component control line shall be laid to the exterior wall according to the design drawings to control the components at the same level. When constructing the outer frame, consider the characteristics of the equipment and the outer frame size of the outer frame to ensure that the outer frame of the equipment has a satisfactory distance.

在誤差大于5毫米時，接線裝置應光滑、光滑。部件接頭處應留有間隙，并按設計要求處理。防水部應做防水處理，并采取必要的防凍措施。顯露于空氣中的鏈節和焊接應該被可靠地腐蝕。

When the error is greater than 5mm, the wiring device shall be smooth and smooth. Gaps shall be reserved at the joints of components and treated according to the design requirements. Waterproof treatment shall be carried out for the waterproof part, and necessary anti freezing measures shall be taken. Chain links and welding exposed to air shall be reliably corroded.

固定樁錨節點的方法：外裝修構件采用現澆混凝土結構，其實際強度等級大于C20，厚度大于1.5mm，厚度大于100mm。采用直徑不小于8毫米的地腳螺栓。如伸縮螺栓不符合以上要求，應采用焊接連接裝置。

Method of fixing pile anchor node: cast-in-place concrete structure is adopted for exterior decoration components, with actual strength grade greater than C20, thickness greater than 1.5mm and thickness greater than 100mm. It is recommended to use anchor bolts with a diameter of no less than 8mm. If the expansion bolt does not meet the above requirements, the welding connection device shall be used.

依據結構圖確定外墻裝飾件的安裝位置為彈出式定位。翻轉后粘貼網格布。如有特殊情況，不需旋轉包裝即可直接粘貼。采用薄層全粘方法粘貼，用力擠壓各部位，使砂漿外溢，膠縫寬度不超過3mm。用鉤子把膠縫固定住，灰縫要填滿，零件表面要保持干凈。

According to the structural drawing, the installation position of exterior wall trim is determined as pop-up positioning. Flip and paste the grid cloth. In case of special circumstances, it can be pasted directly without rotating the package. The thin layer full bonding method shall be adopted for pasting, and each part shall be forced to make the mortar overflow. The width of the glue joint shall not exceed 3mm. Fix the glue joint with a hook, fill the mortar joint, and keep the part surface clean.

安裝時，如需拼接，應事先測量拼接的尺寸和角度。預接合應在平面上，接合位置不得超過3毫米。膠合砂漿作為粘接材料可提高砂漿的稠度，并可采用薄層全膠合的方法。接合時，需輕壓均勻，錘打使灰縫符合要求。

During installation, if splicing is required, the size and angle of splicing shall be measured in advance. The pre jointing shall be on a flat surface and the jointing position shall not exceed 3 mm. As a bonding material, the bonding mortar can improve the consistency of mortar, and the thin layer full bonding method can be used. The joint shall be pressed gently and evenly, and the mortar joint shall meet the requirements by hammering.

以上講解完畢了，相信大家已經對外墻裝飾有了一個全新的認識，再提醒一點，裝飾完工后，在外墻裝飾構件的接縫干燥后，將專用的抗裂膠用于接縫處處理。當完成時，一定要注意保護成品，并嚴禁踐踏和重物。關注我們http://www.libpo.com.cn，了解更多事項！

After the above explanation, we believe that you have a new understanding of the exterior wall decoration. One more thing to remind us is that after the decoration is completed, after the joints of the exterior wall decoration components are dry, special crack resistant adhesive will be used to treat the joints. When finished, pay attention to protect the finished products, and prohibit trampling and heavy objects. Follow us http://www.libpo.com.cn , learn more!