GRC構件以其簡便易安裝，美觀等優勢一直深受人們的喜愛與歡迎，GRC構件在建筑中做為外墻裝飾一直發揮著重要作用。但是很多人并不了解GRC構件是如何進行安裝的，下面，GRC構件廠家帶大家一起了解一下GRC構件的安裝方法，以及GRC構件的日常維護，希望能幫助到你!
GRC component has been loved and welcomed by people for its advantages of easy installation and beautiful appearance. GRC component has been playing an important role in building as exterior wall decoration. But many people don't know how to install GRC components. Now, GRC component manufacturers will take you to understand the installation method of GRC components and the daily maintenance of GRC components, hoping to help you!
1.GRC有鋼框架梁。安裝前，將角碼或角鋼固定在墻上，作為與鋼骨架的焊接點。當安裝截面尺寸大于300 mm小于1000 mm(無鋼骨架)的構件時，在保溫層上畫出預埋件，用角磨機切割保溫層，用膨脹螺栓將GRC構件的預埋鍍鋅預埋件與墻體固定，并對接縫進行防腐處理，修補接縫。截面尺寸小于300毫米的構件通過保溫層用膨脹螺栓直接固定在墻上。注意保證螺栓的錨固長度。
1. GRC has steel frame beam. Before installation, the corner code or angle steel shall be fixed on the wall as the welding point with the steel framework. When installing the components with section size larger than 300 mm and less than 1000 mm (without steel framework), draw the embedded parts on the insulation layer, cut the insulation layer with an angle grinder, fix the embedded galvanized embedded parts of GRC components with the wall with expansion bolts, and carry out anti-corrosion treatment on the joints to repair the joints. The components with section size less than 300 mm are directly fixed on the wall with expansion bolts through the insulation layer. Pay attention to ensure the anchorage length of bolts.
2.玻璃纖維增強復合材料窗蓋的安裝：玻璃纖維增強復合材料構件應沿窗框外的墻壁安裝。注意膨脹螺栓的緊固位置，避免抹灰層。當安裝垂直窗邊緣或立柱各樓層標高時，應注意調整垂直誤差。
2. Installation of glass fiber reinforced composite window cover: glass fiber reinforced composite components shall be installed along the wall outside the window frame. Pay attention to the fastening position of expansion bolts to avoid plastering. When installing the vertical window edge or column to the elevation of each floor, pay attention to adjust the vertical error.
3.安裝構件時，如果構件的預埋件遇到空心磚，用延伸螺栓穿墻或在上下主體結構部位延伸角鋼來固定安裝節點。
3. When installing the component, if the embedded parts of the component meet the hollow brick, use the extension bolt to pass through the wall or extend the angle steel at the upper and lower main structure to fix the installation node.
4.GRC收口部位的處理，如女兒墻壓頂、窗臺板、窗墻等部位，要美觀、防水，嚴格按照工序施工(由土建施工單位做流水)。
4. GRC closing parts, such as parapet coping, window sill plate, window wall and other parts, shall be beautiful and waterproof, and shall be constructed in strict accordance with the process (the civil construction unit shall be responsible for the flow).
GRC構件廠家認為，固化意味著GRC組件脫模后，應注意避免陽光、風和空氣中低濕度的影響。在后固化過程中，有必要采取一些簡單的方法來避免儲存過程中的陽光直射。
GRC component manufacturers believe that curing means that after demoulding GRC components, attention should be paid to avoid the influence of sunlight, wind and low humidity in the air. In the post curing process, it is necessary to take some simple methods to avoid direct sunlight during storage.
GRC構件通常壁比較薄，水灰比較低，而GRC懸掛板的表面積較大。因此，應采用有效的維護系統來實現理想的維護。總而言之：
The wall of GRC members is usually thin and the water cement ratio is low, while the surface area of GRC suspension plate is large. Therefore, an effective maintenance system should be adopted to achieve the ideal maintenance. to make a long story short:
如何進行日常維護?
How to carry out routine maintenance?
1.盡量避免灰塵和污漬。如果表面有灰塵或污漬，你可以用真空吸塵器清潔，并確保真空吸塵器是一個軟刷，因為硬字可能會劃傷砂巖。
1. Try to avoid dust and stains. If there is a scratch on the surface of a hard vacuum cleaner, and make sure you use a vacuum cleaner to clean the dirt.
2.安裝后盡快密封：密封口可作為保護層，能很好地防止砂巖中的灰塵、污漬進入和水分蒸發，否則會在與空氣中的物質反應時損壞。
2. Seal as soon as possible after installation: the sealing opening can be used as a protective layer, which can well prevent the dust and stains in the sandstone from entering and water evaporation, otherwise it will be damaged when reacting with substances in the air.
3.不要接觸油漬：油或污垢會導致砂巖背景墻染色。如果有接觸，要盡可能清潔。
3. Do not touch oil stains: oil or dirt will cause staining of sandstone background wall. If there is contact, be as clean as possible.
以上就是GRC構件廠家整理的幾點關于GRC構件的安裝與維護方法，在這里要提醒大家，GRC構件在清潔維護的時候使用溫水和干凈的布，可以防止污漬沉積，避免表面損壞。相信通過本文的描述，你能夠對GRC構件有一定的認識和了解，希望以上內容能幫助到你。另外，若你想要了解更多相關資訊，可以多多關注我們的網站動態。
The above are the GRC component manufacturers to sort out a few points about the installation and maintenance methods of GRC components. Here I want to remind you that the use of warm water and clean cloth in the cleaning and maintenance of GRC components can prevent the deposition of stains and avoid surface damage. I believe that through the description of this article, you can have a certain understanding of GRC components. I hope the above content can help you. In addition, if you want to know more about it, you can pay more attention to our website.
