GRC構件在我們現在的生活中非常重要，而GRC構件一般安裝在室外，經常暴露在風雨中，導致各種情況會出現，那么GRC構件的一般要求應考慮哪些要素？了解這些內容更好使用它！

　　GRC components are very important in our life now, and GRC components are generally installed outdoors, often exposed to wind and rain, resulting in various situations, so what elements should be considered in the general requirements of GRC components? Know this content and use it better!

　　GRC構件安裝完畢后，停止對GRC構件進行防水漆或油漆的維護。這主要是為了避免水分蒸發。另一方面是防止與空氣接觸，從而使內部鋼筋生銹而失去使用。當然，一段時間后涂層會被風化，因此需要再次停止使用，并定期停止清潔。使用一段時間后，GRC表面會有很多污漬。

　　After the INSTALLATION of GRC components, stop the maintenance of waterproof paint or paint on GRC components. This is mainly to prevent evaporation of water. On the other hand is to prevent contact with the air, so that the internal steel rust and lose use. Of course, the coating will be weathered over time, so it needs to be stopped again and cleaned regularly. After a period of use, GRC surface will have a lot of stains.

　　我們可以用80以下的高壓水槍停止清洗，但力度不能太大，否則會損壞零件。應特別注意定期停止這種清潔要求；避免陽光直射。避免使用瓷磚清洗劑進行清潔，因為它會使瓷磚褪色，就應用干凈的軟布和溫水，并經常進行擦拭可以防止有害化學物質的沉積，而傷害表面對于室外組件，這個說法可能不完整，但對于室內GRC構件，防止陽光直射可以很好地延長其使用壽命。當然，防水涂料也是需要的。

　　We can use a high-pressure water gun below 80 to stop cleaning, but the strength should not be too strong, otherwise the parts will be damaged. Special attention should be paid to discontinuing such cleaning requirements periodically; Avoid direct sunlight. Avoid to use detergent to clean ceramic tile, because it can make the ceramic tile fade, apply a clean soft cloth and warm water, and regular cleaning can prevent the deposition of harmful chemicals, and surface damage for outdoor components, the idea may not be complete, but for indoor GRC components, prevent direct sunlight is a good way to prolong its service life. Of course, waterproof paint is also needed.

　　因此，我們需要采取有效的維護方法和適當的早期強度，以便于脫模和搬運，以保證設計強度，并限制收縮以避免開裂。養護可以使水泥正常水化停止，增強強度和內聚力。它需要大大減少體積損失、收縮和可能的開裂。

　　Therefore, we need to adopt effective maintenance methods and appropriate early strength to facilitate demoulding and handling, to ensure design strength and limit shrinkage to avoid cracking. Curing can make cement normal hydration stop, enhance the strength and cohesion. It requires a significant reduction in volume loss, shrinkage and possible cracking.

　　為了控制水分的流失，簡單來說，補水是固化的基礎，再加上脫模前后的溫度控制，模具通常用干凈的聚乙烯薄膜包裹，這也是為了避免影響濟南GRC構件中的水分蒸發和風，也能附著水分傳熱。此外，在維護的早期階段，GRC部件應具有足夠的強度，以防止在脫模和搬運過程中損壞。特別是在某些地區，需要停止加熱GRC構件以保持溫度在15℃以上。

　　In order to control the loss of water, in simple terms, water refill is the basis of curing, plus temperature control before and after demolstering, the mold is usually wrapped with clean high-quality polyethylene film, which is also to avoid affecting the moisture evaporation and wind in Ji 'nan JI 'nan GRC components, but also attached to water heat transfer. In addition, in the early stages of maintenance, GRC components should be strong enough to prevent damage during demoulding and handling. In particular, in some areas, it is necessary to stop heating GRC components to keep the temperature above 15 ° C.

　　GRC構件的一般要求應考慮哪些要素？問題的講解內容基本上就是這樣了。這就 告誡我們，在使用GRC構件時需要注意的事項不算少，只有多加注意小心維護才能使用時間長久。更多內容就來網站www.libpo.com.cn咨詢！

　　What elements should be considered for general requirements of GRC components? So that's basically what the problem is. This warns us that in the use of GRC components need to pay attention to matters not less, only pay more attention to careful maintenance can use a long time. More content to the website www.libpo.com.cn consultation!